Nicole's™ Bead Shop Celebrate Spring Jewelry Set

Back to category
by Nicole's™ Bead Shop Design Team

Nicole's™ Bead Shop Celebrate Spring Jewelry Set

Amazing stones are the stars in these pieces!

Project Details

  • Level:beginner
  • Time:4 hours

Project Instructions

  • 1
    Necklace: Cut three 15-link strands of double Silver chain.
  • 2
    Cut nine 3-link strands of double Silver chain.
  • 3
    Cut five 2-link strands of double Silver chain.
  • 4
    Create 4 small cube dangles: open an eye pin loop, add 2 link strand of double chain, close eye pin loop. Add Purple cube to eye pin, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, add a closed jump ring, close loop.
  • 5
    On a head pin, add a Blue rondelle, a flat Silver spacer and Blue rondelle, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, connect to the closed jump ring on chain strand, close loop.
  • 6
    Repeat steps 5-6 to create 4 dangles.
  • 7
    Repeat steps 5-6, but replace 2-link chain with 3-link chain.
  • 8
    Create more dangles: Open an eye pin loop, add Purple cube to eye pin, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, add a closed jump ring, close loop.
  • 9
    On a head pin, add a Blue rondelle, a flat Silver spacer and Blue rondelle, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, connect to the closed jump ring, close loop.
  • 10
    Repeat steps 8-9, replacing Purple cube with Purple rectangle.
  • 11
    Create 6 beaded connectors: On an eye pin, add a Blue rondelle, bead cap, Silver round, bead cap and Blue rondelle, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a closed loop.
  • 12
    Repeat step 9 six times.
  • 13
    Create beaded chain: On an eye pin, add a Blue rondelle, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, add a closed jump ring, close loop.
  • 14
    Open an eye pin, connect it to the closed jump ring, add a flat Purple rondelle, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, add a closed jump ring, close loop.
  • 15
    Repeat steps 11 – 12 two more times.
  • 16
    Create v-shaped dangle: Cut two 12-link strands of figure 8 chain.
  • 17
    Open jump ring, add Purple cube dangle, add two 12-link figure 8 chain strands, close jump ring.
  • 18
    Connect pieces to create necklace: On 15 link double chain strand, add two jump rings, add fancy toggle to 2nd jump ring and close.
  • 19
    Repeat step 17 and connect toggle to help keep necklace together.
  • 20
    Open eye pin loop, add closed jump ring, close eye pin loop, add purple rectangle bead, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, add a closed jump ring, close loop.
  • 21
    Open jump ring add closed loop with rectangle bead and attach to 15 link chain strand, close jump ring.
  • 22
    Open jump ring, attach it to the other end of the rectangle bead loop and before closing, add round fancy toggle, close jump ring.
  • 23
    Repeat steps 19-21 on other side of necklace.
  • 24
    Open jump ring, attach to round toggle, add beaded chain, close jump ring.
  • 25
    Repeat step 23 on other side of necklace to complete beaded chain connection.
  • 26
    On the round toggle loop, add a jump ring, a 12-link double chain strand and a 3 link double chain strand, close jump ring.
  • 27
    Repeat step 25 on other side of necklace.
  • 28
    Open jump ring, add to one of the 3 link chain pieces already attached, while still open add beaded connector, close jump ring.
  • 29
    Repeat step 27 on other side of necklace.
  • 30
    Open jump ring, attach to beaded connector, add 3-link double chain piece, close jump ring.
  • 31
    Repeat step 29 on other side of necklace.
  • 32
    Repeat steps 27-29 two more times.
  • 33
    Open jump ring, attach two jump rings, add a rectangle bead dangle, close jump ring.
  • 34
    Open one of the two jump rings, attach to one of the 3 link chain pieces already attached, close jump ring. Repeat for the other 3 link chain piece.
  • 35
    Add 5 dangles to chain beneath the beaded chain. Add 2 link dangle to 4th chain link, 6th link, 10th chain link and 12th chain link. Add 3 link dangle to 8th chain link.
  • 36
    Add v-shaped dangle by opening jump ring, attach one of the figure eight chain strands to the jump ring just above the 2nd beaded connector.
  • 37
    Repeat for other side of necklace.
  • 38
    Bracelet: Cut 8 strands of figure eight chain, 12 links each.
  • 39
    Use cutter to remove pendant loop.
  • 40
    Use two pliers to open jump ring, find the middle of the pendant and put the jump ring through opening and close jump ring.
  • 41
    Open 2nd jump ring, add strands of chain, connect jump ring to pendant jump ring and close.
  • 42
    Connect 3rd jump ring to end of the 4 strands of chain, add toggle clasp, close jump ring.
  • 43
    Repeat steps 41 to 43 to complete other side of bracelet.
  • 44
    Earring (make 2): Cut two pieces of figure eight chain, 23 links each.
  • 45
    Add 1 flat sided Purple bead to an eye pin, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, count to the 12th chain link, add it to the loop wire, close loop using round nose pliers.
  • 46
    Gently open the loop on another eye pin, connect it to the original eye pin on the flat Purple bead, use flat nose pliers to close loop.
  • 47
    Add long acrylic bead to eye pin, bend remaining wire to 90 degree angle, use cutter to trim leaving 1/4 inch. Use round nose pliers to make loop.
  • 48
    Open a jump ring using two pairs of pliers, add a second jump ring and connect to the eye pin on the long acrylic bead.
  • 49
    Open the top jump ring, add ear wire, close jump ring.

Project Details

  • Level:beginner
  • Time:4 hours

Project Supplies

  • Nicole's™ Bead Shop Strand Bead Mix Silver/Grey with Rounds 235 pc. 104800975
  • Nicole's™ Bead Shop Strand Light Purple Beads with Silver Spacers 104801465
  • Nicole's™ Bead Shop Strand Flat Rondelles Purple 104801579
  • Nicole's™ Bead Shop 6 x 8 mm Glass Rondelle Beads Purple 64 pc. 104800747
  • Cousin Jewelry Basics Filigree Metal Round Accent Silver/Purple 104561670
  • Cousin Jewelry Basics Figure 8 Chain 64 inch Silver 104789791
  • Cousin Jewelry Basics Jump Rings 6 mm Open and Closed Silver 300 pc. 104563252
  • Cousin Jewelry Basics Double Link Chain Silver 43 inch 104789796
  • Cousin Jewelry Basics 8 Set Closure Pack Silver 104563391
  • Cousin Jewelry Basics Mixed Cap Silver 30 pc. 104563113
  • Cousin Jewelry Basics Eye Pins Silver 180 pc. 104562320
  • Cousin Jewelry Basics Head Pins Silver 180 pc. 104563082
  • Cousin Tool Basics Value Pack 3 pc. 104257385
  • Panacea Heavy Duty 8 inch Wire Cutters 104455865
  • Flush Cutter