Nicole's™ Bead Shop Rebecca Earrings, Necklace and Bracelet

Back to category
by Nicole's™ Bead Shop Design Team

Nicole's™ Bead Shop Rebecca Earrings, Necklace and Bracelet

Gold goes with everything!

Project Details

  • Level:beginner
  • Time:4 hours

Project Instructions

  • 1
    Bracelet: Add a jump ring onto the end of either side of the plastic link chain. On one end add another jump ring to the new jump ring, and on the other end add a lobster claw clasp. Cut five pieces of beading wire approximately 5 inch in length. Use a crimp bead to crimp one end of the wire onto the jump ring on last link of the plastic chain. String on an oval bead and then crimp the wire onto the jump ring on the other side of the link. Use wire cutters to trim away extra wire. Complete for all five chain links.
  • 2
    Necklace: String 9 square beads onto eye pins and create a loop on the other side. Do the same for 8 Gold spacer beads and 4 oval beads. Connect the beads in this pattern: Square bead, spacer, square bead, spacer, oval bead, repeat. This should create a 17 inch strand of beads. Set aside. Using the smaller Copper chain, cut one strand using wire cutters to 20-1/2 inch, 2 pieces of 5 inch, 2 pieces of 10 inch, and one 30 inch strand. Take the strand of chunky Gold chain and thread one piece of the 10 inch chain through the last link on either side. Open a jump ring and attach the skinny chain ends onto the jump ring. Take the strand of beaded links and open the loop on the end of either side and attach one piece of the 5 inch chain on either side. Open back up the jump ring that is holding the other chain ends and string on the beaded link chain ends. Onto the outer side of the jump ring add on the 30 inch strand of chain and on the inner side of the jump ring add the 20-1/2 inch strand of chain. Close the jump ring. Add another jump ring onto each side, and onto one jump ring add a lobster claw clasp.
  • 3
    Earrings: Using wire cutters, cut 2 lengths of chain with 19 links in each chain. Set aside. String 4 rondelle beads onto an eye pin and form a loop on the other side. Open up the loop ends and string on both pieces of chain, one on the bottom and one on the top. Close each loop with needle nose pliers. On the top piece of chain find the center of the chain and use needle nose pliers to attach an earring hook to the center link.
  • 4
    Open one of the two jump rings, attach to one of the 3 link chain pieces already attached, close jump ring. Repeat for the other 3 link chain piece.
  • 5
    Add 5 dangles to chain beneath the beaded chain. Add 2 link dangle to 4th chain link, 6th link, 10th chain link and 12th chain link. Add 3 link dangle to 8th chain link.
  • 6
    Add v-shaped dangle by opening jump ring, attach one of the figure eight chain strands to the jump ring just above the 2nd beaded connector.
  • 7
    Repeat for other side of necklace.
  • 8
    Bracelet: Cut 8 strands of figure eight chain, 12 links each.
  • 9
    Use cutter to remove pendant loop.
  • 10
    Use two pliers to open jump ring, find the middle of the pendant and put the jump ring through opening and close jump ring.
  • 11
    Open 2nd jump ring, add strands of chain, connect jump ring to pendant jump ring and close.
  • 12
    Connect 3rd jump ring to end of the 4 strands of chain, add toggle clasp, close jump ring.
  • 13
    Repeat steps 41 to 43 to complete other side of bracelet.
  • 14
    Earring (make 2): Cut two pieces of figure eight chain, 23 links each.
  • 15
    Add 1 flat sided Purple bead to an eye pin, bend remaining wire to a 90 degree angle, use cutter to trim leaving 1/4 inch. Use the round nose pliers to make a loop, before closing loop, count to the 12th chain link, add it to the loop wire, close loop using round nose pliers.
  • 16
    Gently open the loop on another eye pin, connect it to the original eye pin on the flat Purple bead, use flat nose pliers to close loop.
  • 17
    Add long acrylic bead to eye pin, bend remaining wire to 90 degree angle, use cutter to trim leaving 1/4 inch. Use round nose pliers to make loop.
  • 18
    Open a jump ring using two pairs of pliers, add a second jump ring and connect to the eye pin on the long acrylic bead.
  • 19
    Open the top jump ring, add ear wire, close jump ring.

Project Details

  • Level:beginner
  • Time:4 hours

Project Supplies

  • Nicole's™ Bead Shop Brown Swirl Faceted Oval Beads with Spacer 17 pc. 104801031 (2)
  • Nicole's™ Bead Shop Octagon Linked Chain Light Amber Faceted Beads 5 pc. 104801337
  • Nicole's™ Bead Shop Acrylic Beads Gold Rose 22 pc. 104801335
  • Nicole's™ Bead Shop Acrylic Cube Links Peach 10 pc. 104801543
  • Cousin Jewelry Basics Starter Pack Gold 145 pc. 104563633 (5)
  • Cousin Jewelry Basics Chain Small Oval 100 inch Copper 104525158
  • Cousin Jewelry Basics Open Link Chain Gold 30 inch 104744432
  • Cousin Jewelry Basics 4 mm x 8 mm Rondelle Beads Gold/Crystal 8 pc. 104563575
  • Cousin Tool Basics Value Pack 3 pc. 104257385
  • Flat Nose Pliers
  • Crimping Pliers
  • Gold Beading Wire (1 package)