Nicole™ Crafts Top Hat Snowman Ornament

Back to category
by Nicole™ Crafts Design Team

Nicole™ Crafts Top Hat Snowman Ornament

Follow some simple instructions and use some basic supplies to make the Nicole™ Crafts Top Hat Snowman Ornament! And with all the supplies that are available at A.C. Moore, you'll want to make it the place you shop for all your Christmas decorating needs!

Project Details

  • Level:intermediate
  • Time:1 hour

Project Instructions

  • 1
    Remove cap from 100 mm ornament and remove metal loop. Fill ball with snowflakes using funnel. Add a few drops of Glue-All adhesive to inside of cap and glue in place. Repeat this exact process for 80 mm ornament.
  • 2
    Glue bottom of small glass ornament to cap of large glass ornament using Glue-All; allow to dry overnight.
  • 3
    Cut two 1-1/2 inch x 8-1/2 inch strips of Red Felt and glue together to form scarf. Tie scarf around cap of large ornament and embellish with rhinestone.
  • 4
    Punch 3 larger circles from Black glitter foam adhesive sheets. Attach to large ornament for snowman’s buttons. If you do not have a 1/2 inch hole punch, trace the size onto the foam and cut it out.
  • 5
    Cut a 3 inch piece of Orange chenille stem. Wind stem around a pencil to form nose. Hold one end of coiled stem and bend opposite end in to form point of nose. Glue to center of small ornament.
  • 6
    Punch 5 smaller circle punches from Black glitter foam adhesive sheets. Attach to face for mouth as shown. If you do not have a 1/4 inch hole punch, trace the size onto the foam and cut it out.
  • 7
    Glue on wiggle eyes.
  • 8
    Download and print project template. Use template to cut shapes from glitter foam, using the color of foam specified on the template. Peel backing from rectangle shape and bend shape to form top of hat. Overlap ends just enough for them to adhere to each other. Place top of hat directly over cut-out section of brim. Bend cut-out sections of brim up inside top of hat to secure in place. Note: even though inside of hat is sticky, a few drops of hot glue are recommended to insure hold.
  • 9
    Cut a 14 inch piece of Red ribbon. Slide one end of ribbon piece through cap loop and tie a knot for hanger. Slide ribbon hanger through hat and secure hat to top of ball using a few drops of hot glue. Embellish hat with glitter leaves and tinsel pom poms as shown.

Project Details

  • Level:intermediate
  • Time:1 hour

Project Supplies

  • Nicole™ Crafts Glass Ball Ornaments 80 mm 4 pc. 104555860
  • New Image Group Felt Sheet 9 inch x 12 inch Red 104276451
  •  Nicole™ Crafts Chenille Stems 6 mm 75 pc. Orange 104277523
  • Nicole™ Crafts Foam Zone™ Adhesive Back 9 inch x 12 inch Sheet Glitter Black 104468064
  • Nicole™ Crafts Foam Zone™ Adhesive Back 9 inch x 12 inch Sheet Glitter Green 104468071
  • Nicole™ Crafts Rhinestones 25 pc. Round Crystal 18 mm 104240560
  •  Nicole™ Crafts Tinsel Pom Poms 50 pc. 7 mm Red 104277832
  • Nicole™ Crafts Wiggle Round Eyes 15 mm 144 pc. 104234522
  •  Buffalo Snow Flakes™ 2 oz. 104591368
  • Hole Punch 1/2 inch
  • Hole Punch 1/4 inch
  • Elmer’s® Glue-All® All-Purpose Glue 16 oz. 104148258
  • Nicole™ Crafts Dual Temperature Trigger Glue Gun 104180411
  • Surebonder® All Purpose Stik™ Glue Sticks 4 inch 50 pc. 104737928
  • Nicole™ Crafts Plastic Funnel 2-1/2 inch Diameter 104183161
Download Project Template